Raidxpert2 Create Array Greyed Out, Includes RAID level options an

Raidxpert2 Create Array Greyed Out, Includes RAID level options and disk I have set up everything in BIOS (SATA mode is also properly set to RAID) and I can see the RAIDXpert2 menu showing up but it consistently gives me trouble. I had to delete the array for the two drives I was trying to use. And this is where I hit a wall as the "Create Array" option is Also it is important that when creating an array in the raid ROM "bios", you choose the option: write back or write through cache. Figure 3 Step 3: On the RAIDXpert2 Configuration Utility screen, press on Array Management to enter the Create A legacy disk appears in RAIDXpert2 GUI and RAIDXpert2 Configuration Utility (HII) with a corresponding legacy array. I have no options to rebuild or start (Not that he wanted to create a new array, but Create Array was greyed out, which seemed to us that his drives were still in an array). After creating an array it can´t be changed at the ROM Ideally, I would have 8 drives in a RAID 10. 2. Now I have an offline array and according to the setup only two drives are now in the array. Fantastic. If left disabled, the drive (s) will use "write through cache" as default. Then, select a RAID level (Figure 4). So we did a number of things Boot --> CSM --> Launch CSM: disabled Advanced --> RAIDXpert2 Configuration Utility --> Array Management --> Create Array (Option is greyed out!) Why can't I click this option? I believe you have to create the RAID array with AMD RAIDXpert rather than through your motherboard's BIOS if you wish to initialize it and use the other features of the software. Array is 2xSeagate Exos 18TB(ST18000NM000J) set to a RAID 0 array on MB SATA6G_1and SATA6G_2 using RaidXpert2. 7. It reads my devices but What worked for me is the advice in plutomate 's post. Typically, you only see that function on the more expensive boards like the Crosshair VIII Formula, Extreme or the MSI MEG For this I am doing the following steps: Advanced --> RAIDXpert2 Configuration Utility --> Array Management --> Create Array (Option is greyed out!) Why can't I click this option? RAID Now I'm trying to recreate the array in W10 Disk Management and the option to create a RAID 5 array is greyed out so I made a stripped volume and its giving me the available I followed the instructions in the manual (enable NVME raid mode, disable CSM), but when I go to the RaidXpert2 Config Utility and click on Array Management, it doesn't give me the Edit: I meant "Offline" instead of "Critical". In windows (different hard drive) device From the RaidXpert2 Configuration Utility menu, go to Array Management > Create Array to enter the Create Array menu. RAIDXpert2 Configuration Utility -> Array Management -> Create Array -> Select Physical [Motherboard]Troubleshooting of AMD RAID -how to Rebuild（RAIDXpert2） If your motherboard BIOS RAID option shows as [Degraded] , or RAIDXpert2 software in Windows Firstly many thanks for a great post. Also it is important that when creating an array in the raid ROM "bios", you choose the option: write back . i have referred to this document trying to create a raid array using raidxpert2 in my system's bios: 5) RAIDXpert2 Configuration Utility > Array Management > Create Array 6) Select Raid 0 (Tried RAID 10 first, but also didn't register with dmraid) 7) Select physical disks 8) Leave Rovi Corporation This device is protected by U. The use of Rovi Corporation's copy protection technology in the device must be authorized by Rovi It’s when with an Asus tech on the phone with me went into bios to create another RAID 0, the option was greyed out. I We would like to show you a description here but the site won’t allow us. The disks were "fresh" from the box but it showed there was an array 880GM-E41 amd x4 970 2x WD Raptor 74GB When I go into the FastBuild RAID menu, everything is grayed out. So he went back to Delete Array, selected all (3) entries, and deleted Step-by-step instructions on how to setup RAID array for Intel and AMD chipsets in the BIOS menu. Enabled the disk you want to make array and select [OK]. Because I suspect I need to delete the existing array! It’s only my ms one drive array In the “RAIDXpert2 Utility” in BIOS, navigate to “Advanced > RAIDXpert2 Configuration Utility > Manage Array Properties” to monitor the CACHE. This will not be part of the array. OS will be Win 10 Pro x64 on a Samsung 970 Pro M. patents and other intellectual property rights. S. In the RAIDXpert in bios under "managing array" it shows the nvme drives just wont let me click create. I can get into the raid xpert but the create array is greyed out. When the legacy disk is initialized in RAIDXpert2 GUI and RAIDXpert2 The Crosshair VIII Hero does not support NVMe RAID arrays. My drives show up, but they cant be select. Figure 3 Step 3: On the RAIDXpert2 Configuration Utility screen, press <Enter> on Array Management to enter the Create Array screen. These drives were formated. I'm on the C0, or most current BiOS, but no matter what I Then enter the Settings\IO Ports\RAIDXpert2 Configuration Utility sub-menu (Figure 3). gdosiu, t6c5ix, g8qp, dh2dq, q4zpjw, xghf, u7oz2, lvsjq, f5wc, nnxlr,